Ask technical questions about your Ford Bronco II here. Technical write-ups on your axle swaps, engine swaps, chop tops, etc. are encouraged.
JAMES DUFF PRORATE COILS
Replies: 1
by
fullsizebronc »
Sat Dec 04, 2004 3:06 pm
I HAVE A FULLSIZE 80' BRONC AND A SRAIGHT AXLE 44 IN FRONT. I LOVE THE TRAVEL WITH THE 3.5 S ON A BII BUT WHAT SIZE SHOULD I RUN FOR A 1/2 TON...
1 Replies
1379 Views
Last post by FatMan
Sat Dec 04, 2004 3:30 pm
chop top question
Replies: 2
by
OCD4B2 »
Thu Dec 02, 2004 5:52 pm
:D I'd really like to know how to make a really clean looking bronco II chop top. I've looked around and seen some real nice work and then some real...
2 Replies
1904 Views
Last post by OCD4B2
Sat Dec 04, 2004 3:10 am
Hi-Po V6
Replies: 13
by
dave-stjohn »
Tue Nov 30, 2004 8:48 am
since I'm already here I thought I'd throw out this ?, does anyone make performance parts for the 2.9L I already have in my B2, or do I have to go...
13 Replies
5611 Views
Last post by dave-stjohn
Thu Dec 02, 2004 11:53 am
My Bronco
Replies: 8
by
kylebronco2 »
Tue Nov 30, 2004 11:19 am
Im kind of new to all this 4x4ing and customizing broncos...but basically im plannin on gettin a body lift for my 86 bronco 2, and a suspension lift...
8 Replies
4490 Views
Last post by kylebronco2
Thu Dec 02, 2004 11:38 am
11 Replies
4762 Views
Last post by bnmwilliams
Wed Dec 01, 2004 11:02 pm
94 mustang question
by
OCD4B2 »
Wed Dec 01, 2004 10:26 pm
I wanna know if the auto trans, from a 94-95 mustang, was an AOD :confused: . I've heard that these were only AOD-E and i REALLY REALLY want to make...
0 Replies
1931 Views
Last post by OCD4B2
Wed Dec 01, 2004 10:26 pm
BroncoII tach's
Replies: 5
by
dave-stjohn »
Mon Nov 29, 2004 7:13 pm
I have a 86 B2 and the tach doesn't work, the needle was broken off so I went ahead and got a new one from the boneyard and it doesn't work either,...
5 Replies
2245 Views
Last post by DBrown
Tue Nov 30, 2004 7:48 pm
bump stops
Replies: 7
by
OCD4B2 »
Mon Nov 22, 2004 7:45 pm
Bump stops, need some new ones, cant find em where i want em. Been botteming out my suspension too much, they were holding up good. But i jumped it...
7 Replies
3225 Views
Last post by OCD4B2
Mon Nov 29, 2004 4:05 pm
carrier swap?????
Replies: 8
by
FatMan »
Thu Nov 25, 2004 12:29 am
well i pulled my rear apart tonight and i have 31 spline axle shaft's :frown: . not that im complaining but the detroit i have is for 28 spline....
8 Replies
3546 Views
Last post by b2binbad
Sun Nov 28, 2004 11:32 am
87-93 and 94-95 302 questions
Replies: 2
by
OCD4B2 »
Fri Nov 26, 2004 4:02 pm
Ok :D , i got my 302 and its a 1990 5.0 HO. My computer on the other hand is a 1995. I'm gonna be running an AOD for now because i want a 4th speed...
2 Replies
1382 Views
Last post by OCD4B2
Sat Nov 27, 2004 11:21 pm
Fuel Rail
Replies: 1
by
FBII »
Fri Nov 26, 2004 6:52 pm
I am looking for a fuel rail for a 1989 Bronco II. I went to my local Ford dealer and they tell me that they are obsolete. Tried to look on internet...
1 Replies
974 Views
Last post by FatMan
Sat Nov 27, 2004 2:28 pm
Heater Core replacement
Replies: 4
by
ran429 »
Fri Nov 26, 2004 9:04 am
How hard is it to remove and reinstall a heater core in an 84 B-II ?
4 Replies
2654 Views
Last post by Nobody
Sat Nov 27, 2004 8:20 am
Just Thinking....
Replies: 16
by
Phillippi »
Wed Aug 18, 2004 2:39 am
Ok, I HAD a 3.5 TTB lift and I liked the height. Now If I go with a 3.5 duff for EB and a 5.0L how much over STOCK should I get (approx)? I dont...
16 Replies
7601 Views
Last post by Phillippi
Thu Nov 25, 2004 9:59 pm
4wd conversion?
Replies: 3
by
jhestess5 »
Wed Nov 24, 2004 8:17 pm
Would any one know what it would cost to buy all the parts needed to make my 88 bronco 2 a 4wd???
3 Replies
2031 Views
Last post by Happy_Jack
Thu Nov 25, 2004 6:32 pm
tranny again!!!!!!!
Replies: 8
by
Trigger_2001 »
Mon Nov 22, 2004 6:58 pm
why is it that when i went to put my 88 b2 in first, it acted like you were towing a house?? i locked in 4x4 and finally pulled it out of whatever....
8 Replies
3733 Views
Last post by 85ranger4x4
Wed Nov 24, 2004 10:49 am
rattling/thumping noise
Replies: 5
by
bIIcool »
Mon Nov 22, 2004 11:49 am
I have a 1990 Bronco II with a 5 speed manual transmission. Just last week I started hearing a rattling noise. It goes away when I press the clutch...
5 Replies
2547 Views
Last post by DBrown
Tue Nov 23, 2004 8:42 pm
how to lift my 85 B II
Replies: 5
by
fordboy »
Sat Nov 20, 2004 7:52 am
this is just for trail use.I want to lift the front by homemade stuff.this is never gonna touch the street,Tell me what to do I know somebodies done...
5 Replies
3244 Views
Last post by DBrown
Mon Nov 22, 2004 12:13 pm
Dana 44 trac bar question
Replies: 7
by
OCD4B2 »
Wed Nov 17, 2004 10:57 pm
Ok can i buy a trac bar for the dana 44 from someone? I dont want to custom fabricate something this important and mess it up....i would :D . Give me...
7 Replies
2645 Views
Last post by OCD4B2
Thu Nov 18, 2004 10:40 pm
New Member, Need Some 302 Tranny Info
Replies: 11
by
Kris »
Tue Nov 16, 2004 8:15 pm
what i am wanting to do is throw a carb. 302 in my truck, i cant handle these 2.8's, ive went through one allready, and the second is leaking oil,...
11 Replies
3997 Views
Last post by wilber
Thu Nov 18, 2004 4:36 pm
steering question
Replies: 11
by
DBrown »
Wed Nov 17, 2004 8:27 am
I was looking for the kit or info on flip the steering to the top if the knuckle instead of on the bottom. I'm not talking about putting the steering...
11 Replies
4363 Views
Last post by DBrown
Thu Nov 18, 2004 11:00 am
Traction Bar!
Replies: 8
by
Rockcrawler »
Sat Nov 13, 2004 11:21 pm
Well after building up my truck and putting the 44's on my leafs were crying out for help! I broke the staps holding in the u joint so i didnt want...
8 Replies
3503 Views
Last post by broncoo
Wed Nov 17, 2004 5:16 pm
wristed arm welding?
Replies: 21
by
DBrown »
Tue Nov 09, 2004 8:43 pm
ok I used the search function but I didn't find what I needed.........what rod would y'all use to weld up a wristed arm?
21 Replies
6327 Views
Last post by FatMan
Mon Nov 15, 2004 9:37 pm
Any Idea?
Replies: 2
by
Phillippi »
Wed Jul 21, 2004 11:49 am
Well I am trying to figure out the rear spring setup, as well as the front. For the rear, I remember someone saying that you can use F-150 springs as...
2 Replies
1761 Views
Last post by marinebroncoii
Mon Nov 15, 2004 2:14 am
T-18 & NP-208F?
Replies: 6
by
Jbroncoh »
Sun Aug 01, 2004 9:32 pm
O.K. I got my heart set on going 302, C-4, D20 with the '86 BII right. But I don't have them yet so I guess my options are still open. Damn it!! Now...
6 Replies
3043 Views
Last post by marinebroncoii
Mon Nov 15, 2004 2:07 am
new engine question
Replies: 3
by
PKAdetroitWLZ »
Sun Sep 19, 2004 1:25 pm
two parts:
3 Replies
2007 Views
Last post by marinebroncoii
Mon Nov 15, 2004 1:57 am
another question,
by
jhestess5 »
Sun Nov 14, 2004 6:58 pm
My shifter wont stay in drive when i go or drive over a bump it nocks its self out of drive and into OD..........????but good news i am gettin a...
0 Replies
1988 Views
Last post by jhestess5
Sun Nov 14, 2004 6:58 pm
just a few questions
Replies: 15
by
jhestess5 »
Tue Nov 09, 2004 3:58 pm
i have a 1988 bronco 2, 2wd,xl, my stepdad gav it to me a few months ago befor he left for iraq, how hard would it be and how much would it be...
15 Replies
7240 Views
Last post by Happy_Jack
Thu Nov 11, 2004 5:48 pm
Tranny probs
Replies: 5
by
Trigger_2001 »
Fri Nov 05, 2004 9:45 am
There is a grinding sound in my tranny when my clutch is let out on all gears. The tranny guy said it could be the front bearing. Could be costly....
5 Replies
3311 Views
Last post by Trigger_2001
Tue Nov 09, 2004 9:43 am
347 cam question
Replies: 14
by
OCD4B2 »
Thu Nov 04, 2004 10:31 am
I'm gonna be running my 302 up to a 347 stroker, and i was really wondering about the cam. I would probably be adding new heads sometime and will...
14 Replies
5483 Views
Last post by plowboy
Mon Nov 08, 2004 7:35 am
Sick Bronco
Replies: 12
by
papasBronco »
Wed Oct 27, 2004 9:57 am
Don't know what to do? :hmmm:
12 Replies
6256 Views
Last post by huffs
Sun Nov 07, 2004 6:20 pm
Forum permissions
You cannot post new topics in this forumcannot reply to topics in this forumcannot edit your posts in this forumcannot delete your posts in this forumcannot post attachments in this forum