Re: 5.0 Install
Posted: Sun Jul 05, 2009 1:46 pm
the 77 EB maybe. 78/79 and up F150's/broncos . any of the early 302's
Page 8 of 23
Re: 5.0 Install
Posted: Sun Jul 05, 2009 2:21 pm
Alright thanks. I'll put on the other intake Friday and I should be ready to drop it in then. I just hope this motor runs!
Re: 5.0 Install
Posted: Sun Jul 05, 2009 2:56 pm
i could be wrong but those headers look to wide. hope they fit
Re: 5.0 Install
Posted: Sun Jul 05, 2009 10:39 pm
I'll have to measure them. I hope not, they were made for a swap. If I get a low pressure pump do I still need a fuel regulator?
Re: 5.0 Install
Posted: Sun Jul 05, 2009 11:02 pm
Hi, I'm new here but thought I'd chime in. I'm running a stock in-tank fuel pump on my carb'd 302 w/ Edelbrock 1405 in an 88 2WD Bronco II. I STILL have to run a regulator to knock down the pressure. Not sure what carb you'll use but the Edelbrock 1405 does NOT like the 10+ lbs put out by my stock Autozone in-tank pump.
Re: 5.0 Install
Posted: Mon Jul 06, 2009 2:13 am
Do you have a part number? Is it the same as the sending unit that is in there now? I have a new gas tank waiting to be put on so I have to take the guts out anyway. I want the easiest, cheapest solution.
Re: 5.0 Install
Posted: Wed Jul 08, 2009 3:59 pm
onewontwo
what are you using for motor mounts??
what are you using for motor mounts??
Re: 5.0 Install
Posted: Wed Jul 08, 2009 4:53 pm
They are from L&L. Could there be a problem?
Re: 5.0 Install
Posted: Wed Jul 08, 2009 5:10 pm
What is L&L? is this an American store? I heard 5.0l convertible mounts work, out of a '89 I think. I Need to know as I haven't got my engine in yet either. 
Re: 5.0 Install
Posted: Wed Jul 08, 2009 6:02 pm
i used the V6 mount with adapters
Re: 5.0 Install
Posted: Wed Jul 08, 2009 6:12 pm
Looks like your mounts turned out good. I purchased mine from bronco graveyard. This Friday is some little things then next Friday I'll be dropping it in. Won't be running until a trip to the junkyard though. Anyone have any extra parts?
Re: 5.0 Install
Posted: Wed Jul 08, 2009 7:26 pm
you got the double sump oil pan
Re: 5.0 Install
Posted: Thu Jul 09, 2009 3:56 am
Yes, I do.Ranger Dave wrote:you got the double sump oil pan
Re: 5.0 Install
Posted: Fri Jul 10, 2009 12:02 pm
I picked up a 2 wire univerisal fuel pump. It flows 4-7 psi so I shouldn't need a regulator. Can I tie this into the existing wiring and be down with it or do I need to do more?
Re: 5.0 Install
Posted: Fri Jul 10, 2009 12:16 pm
I'd also like to keep my stock power steering, alternator, and a/c. What vehicle should I look to take the brackets from? Does anyone know if I can switch the v-belt pulleys for serpintine ones? If not I'll have to get a system from the yard and wire it in unless there is a vehicle that would be plug and play. Hopefully I can get some help.