What did you do with your Bronco II today?

tekatlarge · Post by **tekatlarge** » Sun Aug 19, 2018 12:00 pm

Wow I been gone a while and people are back to workin on their BIIs.. Nothing going on here I am still building my Hot Rod and waking up every day alive...

Lance Skene · Post by **Lance Skene** » Wed Sep 19, 2018 9:05 pm

Well wakin up everyday is a good sign Tek..Lol

I havent driven any of the BIIs much this summer but winter isnt far off so the old plow truck need to be ready

Lance Skene · Post by **Lance Skene** » Mon Oct 01, 2018 8:40 am

Starting to look like an early winter so I pulled the plow truck into the shop the other day. Topped up all the fluids, checked all the lights wipers and heater, aired up a couple tires. checked the winch. The bump stops at max blade height need a little repair but otherwise its ready for another winter.

tekatlarge · Post by **tekatlarge** » Sun Dec 09, 2018 11:29 am

Well not doing much on BII's these days. Health is still so so. I did start a new MAJOR PROJECT! I bought some property on the Worshington shores. Ocean Shores. I bought it the day before thanksgiving. I am putting up a new house and a new shop. I will be shrinking my new shop about 400 square ft less than the current one.

Man what a pain in the rear. all the permitting and bids from contractors and all the details worked out. I am hoping to be in my new home by June of 2019. Meanwhile I am going on a big weeding out of my BII parts.

Lance Skene · Post by **Lance Skene** » Thu Dec 13, 2018 12:14 pm

Hey Tek... good to hear from ya... building and moving eh, thats an energitic project for sure, hope it goes as planned and keep us posted:)

Lance Skene · Post by **Lance Skene** » Fri Jan 11, 2019 6:47 am

Welcome to the forum Galusha... got some pics of your B2 you can share??

Ive had a mid winter thus far so the B2 snowplow hasnt seen much action. I cleaned out the shop recently so I can get the XLS in and see if I can free up the motor... if not I'll have to bite the bullet and start a motor swap.

tekatlarge · Post by **tekatlarge** » Mon Jan 21, 2019 8:30 pm

Hey Lance, I sure wished you were closer, I have the perfect motor for you....ha ha ha.

offroadohio · Post by **offroadohio** » Fri Jan 25, 2019 5:49 am

Today I sent payment to a guy for a sector shaft and a plate to build a Doubler

Sent from my LM-X410(FG) using Tapatalk

Lance Skene · Post by **Lance Skene** » Fri Jan 25, 2019 6:48 am

tekatlarge wrote:Hey Lance, I sure wished you were closer, I have the perfect motor for you....ha ha ha.

Thats OK... I have enough of my own to pick from.. including a couple 4.0L if I was so inclined.. but Im not so I will be swapping one Cologne 2.8 for another. I quite like those engines once they have the Durospark conversion. My green '84 runs and drives nice but the truck was in an accident before I got it and cant be registered again without jumping thru alot of hoops so I'll likely use that engine in the xls.

offroadohio · Post by **offroadohio** » Mon Jan 28, 2019 4:01 am

Installed some Ford Taurus s h o seat along with some patch panels for the floor

Sent from my LM-X410(FG) using Tapatalk

offroadohio · Post by **offroadohio** » Fri Feb 08, 2019 4:56 am

Flipups

Sent from my LM-X410(FG) using Tapatalk

BroncoII4x4.com

What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?

Re: What did you do with your Bronco II today?