C4 Tranny

Ask technical questions about your Ford Bronco II here. Technical write-ups on your axle swaps, engine swaps, chop tops, etc. are encouraged.
Post Reply
emg_warlock
Posts: 12
Joined: Thu Aug 19, 2004 11:28 pm

C4 Tranny

Post by emg_warlock »

I nead to know where i can find a c4 transmission eqipped for offroad, and with the right connection to the transfer case. Please help me out.
Damn squirrels never leave my head!
DBrown
Posts: 1545
Joined: Mon Apr 19, 2004 5:21 am
Location: Bowling Green, KY

Post by DBrown »

take a C5 from a 84-85 BII. they are basicly the same thing and they will bolt to the V6.
71 Bronco - twin sticked, full width, 2" lift, wristed arm, lots of rust...

http://www.catalystcycles.com
emg_warlock
Posts: 12
Joined: Thu Aug 19, 2004 11:28 pm

Post by emg_warlock »

No, i need to find a c4 equipped for offroad, thats bolting up to a 302, in my bronco II. not just the regular 6 cylinder.
Damn squirrels never leave my head!
DBrown
Posts: 1545
Joined: Mon Apr 19, 2004 5:21 am
Location: Bowling Green, KY

Post by DBrown »

well, the thing is you can use the C4 bellhousing and converter on the C5 and it will bot to the 302 and your transfer case. sooooooo......if you want a built tranny you can have the C5 beefed and use the C4 bellhousing and converter. after doing this you just have motor mounts, headers, wiring, oil filter relocater, fuel pump and radiator to think about. if you are putting the 302 in an 84-85 BII with an auto and A/C you can possibly use the radiator that came in it from the factory and the factory carb with a 302 2bbl intake manifold. this will now set you at motor mounts, headers, oil filter relocater and an electric fuel pump.
71 Bronco - twin sticked, full width, 2" lift, wristed arm, lots of rust...

http://www.catalystcycles.com
User avatar
Nobody
Posts: 2232
Joined: Sun Apr 18, 2004 6:38 pm
Location: Stanwood, WA.
Contact:

Post by Nobody »

The Early Bronco is the only thing I'm aware of that came with a 4wd C4/Dana 20 combo.
DBrown
Posts: 1545
Joined: Mon Apr 19, 2004 5:21 am
Location: Bowling Green, KY

Post by DBrown »

I am confused??? what are you wanting to run?
71 Bronco - twin sticked, full width, 2" lift, wristed arm, lots of rust...

http://www.catalystcycles.com
emg_warlock
Posts: 12
Joined: Thu Aug 19, 2004 11:28 pm

Post by emg_warlock »

I am trying to put a 302 and c4 tranny into my 1990 Bronco II, Advance Adapters has a set-up for me, but its hella expensive, what should i do? I need the right housing connection to go from my c-4 to borg warner 1350 transfer case. Please supply suggestions.
Damn squirrels never leave my head!
DBrown
Posts: 1545
Joined: Mon Apr 19, 2004 5:21 am
Location: Bowling Green, KY

Post by DBrown »

use the C4 bellhousing and converter on the C5 and it will bot to the 302 and your transfer case
71 Bronco - twin sticked, full width, 2" lift, wristed arm, lots of rust...

http://www.catalystcycles.com
Post Reply