Ask technical questions about your Ford Bronco II here. Technical write-ups on your axle swaps, engine swaps, chop tops, etc. are encouraged.
new axles, nobody will be pleased hehe
by
NMB2 »
Sat Mar 05, 2005 12:40 am
ok heres the pic of my 8 axle after i sandblasted and painted it, the 4.11 motive gears are on the way, i changed out the 28spline shafts with...
0 Replies
904 Views
Last post by NMB2
Sat Mar 05, 2005 12:40 am
Window keeps fogging up
Replies: 8
by
masopicman »
Wed Feb 23, 2005 2:12 am
I recently bought an 84 Bronco 2! And the heat works well, yet side windows are always foggy, is this a common thing? or do I need to wash my...
8 Replies
2794 Views
Last post by masopicman
Wed Mar 02, 2005 1:40 am
Rear end
Replies: 11
by
Phillippi »
Fri Jan 14, 2005 9:18 pm
Hey Matt, or anyone who retained their 7.5 ford (w/ a 5.0 swap), how did you connect the the drivetrain to it? Bastard joint, yoke change (to what)??...
11 Replies
2683 Views
Last post by NMB2
Sun Feb 27, 2005 2:15 pm
Body Change
Replies: 5
by
Dreded »
Mon Feb 07, 2005 11:12 am
I was wondering if anyone has done a body switch from a BroncoII to a Regular Cab Rnager I am wanting to take the BII body off and just replace it...
5 Replies
1617 Views
Last post by Exhauster
Sun Feb 27, 2005 8:32 am
leaf or coil?
Replies: 18
by
OCD4B2 »
Wed Feb 02, 2005 12:32 pm
Ok I was wondering about my setup im going to use.... im running full width axels so I would think that leaf sprung would be the way to go. but i...
18 Replies
4301 Views
Last post by no v8? why drive?
Fri Feb 25, 2005 4:24 pm
1 Replies
996 Views
Last post by no v8? why drive?
Thu Feb 24, 2005 2:04 am
lifting Q's, AGAIN
Replies: 4
by
NMB2 »
Fri Feb 11, 2005 9:06 pm
well i fixed the outter axle shaft so i have 4x4 again..i installed the 2 Add-A-Leafs and i actually got 4 of lift. was i supposed to take some leafs...
4 Replies
1515 Views
Last post by no v8? why drive?
Thu Feb 24, 2005 2:00 am
Driveshaft Help
Replies: 2
by
B2JAY »
Mon Feb 21, 2005 12:32 pm
I'm installing a 6 Skyjacker lift on my stock 86 BII and I need rear driveshaft advise. Instead of spending $$$ to have a custom made shaft, I was...
2 Replies
1138 Views
Last post by no v8? why drive?
Thu Feb 24, 2005 1:57 am
more air flow for my bronco
Replies: 6
by
silent_killer »
Sat Feb 19, 2005 12:14 pm
:D i have a 84 with a 2.8 carbureted and i want to increase my air flow into my carburetor :idea: i was thinging a K&N air filter with a filter...
6 Replies
2000 Views
Last post by silent_killer
Wed Feb 23, 2005 2:54 am
2.9 to 2.8 swap
Replies: 14
by
offroadohio »
Sat Feb 12, 2005 2:55 pm
What will it take as far as wiring to convert a 2.9L bII, to run a 2.8 with stock 2.8 ignition? Computer swap, and a couple wire changes?
14 Replies
3558 Views
Last post by offroadohio
Thu Feb 17, 2005 8:02 pm
drop brackets
Replies: 2
by
NMB2 »
Tue Feb 08, 2005 11:45 pm
whats up everyone, im new here....i just bought my 84 Bronco II about a month ago, i have 2 add-a-leafs and 2 lift blocks and i have just bought some...
2 Replies
1007 Views
Last post by Phillippi
Thu Feb 10, 2005 4:17 pm
Bad Fuel Economy
Replies: 12
by
Spark86 »
Mon Feb 07, 2005 8:12 am
My 1986 Bronco II is getting poor fuel economy (around 12-13 MPG). What is causing this? Bad ignition timing?
Sorry for this simple problem and...
12 Replies
3540 Views
Last post by DBrown
Wed Feb 09, 2005 9:59 pm
Bronco II chop top 101:
Replies: 7
by
DBrown »
Tue Feb 08, 2005 3:55 pm
ok, I have had a few questions here lately about the chop top on my Bronco II, so I figured we should probably have a topic on it. I don't have many...
7 Replies
6366 Views
Last post by Nobody
Wed Feb 09, 2005 9:58 pm
Starter turns but won't engage the flywheel
Replies: 10
by
Pokeyo »
Sun Jan 30, 2005 1:03 pm
Hello, I have a 1990 Bronco II with a 2.9l engine. The starter is new, the wires are all new. I have swapped batteries around. Everything is clean as...
10 Replies
3808 Views
Last post by Pokeyo
Wed Feb 09, 2005 1:07 pm
4.0 Tranny?
Replies: 4
by
gullion_a86 »
Tue Feb 01, 2005 12:55 pm
I have an 85' B2 with a 2.8L engine. I'm going to be getting a 4.0L engine and put in it with a four speed tranny. I need to know what trannies will...
4 Replies
1622 Views
Last post by Bob
Thu Feb 03, 2005 7:46 am
302 conversion
Replies: 7
by
gullion_a86 »
Thu Jan 13, 2005 9:37 am
I'm getting a 302 out of my cousin's 94' F-150 4x4 and I wanted to know what all I have to get off of his truck to make it work in my B2? I 'm...
7 Replies
2313 Views
Last post by gullion_a86
Thu Feb 03, 2005 7:30 am
Seat swap FYI..... (added pics)
Replies: 6
by
Bob »
Mon Jan 31, 2005 9:39 pm
Well I FINALLY got my set of Mastercraft Rubicon seats.
Guess what?
Direct bolt-in! ('84 BII)
The left side runners I had to drill out the metric...
6 Replies
2292 Views
Last post by Bob
Wed Feb 02, 2005 8:47 pm
heater core installation
Replies: 3
by
rugbybroncoii »
Thu Jan 20, 2005 4:01 pm
i bought my 88 bronco II xlt last march and it had a faulty heater core, it was disconnected i assume because it leaked. I wasnt worried about it...
3 Replies
1537 Views
Last post by ranger5.0
Tue Feb 01, 2005 8:03 pm
Mercedes Springs
Replies: 6
by
Wes »
Wed Jan 19, 2005 12:38 pm
Just wondering if instead of using JD EB springs for my BII SAS, If anyones used Mercedes Benz G-Wagon coils? They are 23 with no weight on them....
6 Replies
1936 Views
Last post by Wes
Tue Feb 01, 2005 5:03 pm
4 Replies
1403 Views
Last post by jerryusf
Sun Jan 30, 2005 8:12 am
Body swap
Replies: 184
by
DBrown »
Tue Jul 06, 2004 9:37 am
I was looking on the old board for the person that did the cab swap to a full sized frame. can't find it, so who did it?
I bought another tow rig...
184 Replies
35453 Views
Last post by DBrown
Tue Jan 25, 2005 9:35 am
Pilot bearing
Replies: 1
by
Wicked Bronco II »
Thu Jan 13, 2005 12:20 am
I bought a pilot bearing for my 92 4.0 i was wondering is it supposed to stick out? i have about 80% of that pos in there but since i had no previous...
1 Replies
1001 Views
Last post by DZK007
Mon Jan 24, 2005 9:48 pm
where to find gears?
Replies: 19
by
DBrown »
Tue Dec 21, 2004 5:35 pm
looking at buying my gears here pretty soon, where do y'all go? I was looking around on the net and found some good prices but where have y'all got...
19 Replies
3633 Views
Last post by DBrown
Sat Jan 22, 2005 7:07 pm
THROTTLE POSITION SENSOR & IAC MOTOR
Replies: 6
by
Jbroncoh »
Sat Jan 15, 2005 8:57 am
I'm parting an '86 BII, & have a guy that wants the throttle position sensor & IAC motor. Can someone please tell me exactly where these 2 items are...
6 Replies
2165 Views
Last post by FatMan
Mon Jan 17, 2005 8:24 pm
Driveline angles
Replies: 8
by
b2binbad »
Fri Oct 08, 2004 4:56 pm
Need some help. Hit a few piles today to check flex. I've still got the revolver shackles installed. They're coming off, they suck! My question is,...
8 Replies
2317 Views
Last post by b2binbad
Mon Jan 17, 2005 3:53 pm
9" disk conversion.
Replies: 3
by
FatMan »
Thu Jan 13, 2005 10:50 pm
I posted here cuz i just wanted to know of a link for 9 disk brake conversion. I searched all over pirate BB, and maybe im blind but i found all...
3 Replies
1190 Views
Last post by DBrown
Sat Jan 15, 2005 6:44 pm
rear driveshahft questions
Replies: 17
by
jerrysbroncoii »
Thu Jan 13, 2005 5:20 pm
i have a 88' bronco II and i have purchased a 6 skyjacker lift for it. my rear drive shaft is the cv joint style and i know it needs to be changed,...
17 Replies
5058 Views
Last post by jerrysbroncoii
Fri Jan 14, 2005 3:04 pm
Driveshaft issues
Replies: 5
by
89BII »
Mon Dec 27, 2004 10:21 am
I have an '89 Bronco II, 2wd with a 5 speed. The driveshaft in it has cv joints at both ends. Well.........the rear one is going bad (big news huh!)...
5 Replies
1715 Views
Last post by 89BII
Thu Jan 13, 2005 10:16 am
4.3L Info
Replies: 3
by
gullion_a86 »
Tue Jan 11, 2005 12:09 pm
I was just wondering if a 4.3L engine, like one out of a Mustang, would work in a B2? Also what engine would be best in a b2? A 3.0, 4.0, 4.3, or a...
3 Replies
1507 Views
Last post by Nobody
Wed Jan 12, 2005 8:33 pm
new front suspension. (Again)
Replies: 17
by
Rockcrawler »
Sun Jan 09, 2005 7:25 pm
well the old suspension worked good but for the tires i wanted to run the axle was to far back so i decided to push it forward (17 inches) to gain...
17 Replies
3762 Views
Last post by FatMan
Tue Jan 11, 2005 10:39 pm
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum