BroncoII4x4.com

hey guys i have an 89 bII an i currently have a 3 inch body lift an 31x10.50. i am just in the process of building it up to something better.does anyone have any good ideas or pointers or things i should be aware of before i start???? thanks for the help 93 lightning 351 windsor efi, zf tranny with...

i perfer manual for the sole reason of nothing goes wrong with a shift lever. elctronic shift has a switch and a shift motor for the t-case, which could go bad. worse case senario is the motor goes bad and you have to replace it, i wouldn't let shifting type steer your decision either way.

ok i've got a dana 30 from a 93 grand cherokee that i'm going to put in my b2, does anyone have any advice on this as far as setting up control arms, coil springs to use, rear springs to use, i would like to get about four inches of lift can you give more details? is the pumkin on the drivers side?...

How do you test the compressor to see if it's functioning correctly? lost texans right if its out of the truck, if its in the truck, turn on the a/c and jumper the a/c pressure switch and it will turn on the compressor then you can get a accurate freon reading, if it doesn't kick on the a/c clutch ...

vabronconut, thanks for the reply...we will try your suggestions. and Kolton...we'll get it fixed soon enough and don't use that language when posting to your own MOTHER!!! Remember, I still own it....LOL yea KOLTON mind your mother before she spanks you on the bottom and sends you to your room wit...

holly shit kelly what the hell did he beat you with a tire iron????? man i am really sorry to hear this, and you are lucky you made it through it all, and with a positive attitude, hell i would be bitter as hell, probably be in jail myself for hunting down and killing the little bastard and his f-d ...

kelly-

did you figure out what your going to do with it yet?

Have a bad clunk and vehicle jerks about 2" when I go from park to reverse or from reverse to drive and drive to reverse. Neutral and park dont do this. Thought it was u-joints when we first got it so my dad bought a new driveshaft with two u joints. It didnt fix the problem at all. Ive read d...

like what was already sugested, make sure the clutch resevior is full. if thats not the problem get under the truck with someone in the cab and have push the clutch pedal while your watching the clutch itself ( warning wear some kind of glasses) you may have a external slave cylinder or internal, ei...

first the battery,,, it should read about 14 volts fully charged. a bad battery will show 12-14v but will not have the amps to take a load, so like nobody said take it in and have it checked. second- the module on the right side is your start relay and to crank a car the ignition circuit pulls 12v o...

i also read that its between 9 and 12. i really don't know if they include the torque convertor or not in that or one is and ones not. no telling :confused: i would definetly get the stick for it they are pretty common and cheap. i have also read that the early bronco c4 has a slightly deeper pan th...

i tried finding the quantity that tranny holds and some say 9qts. i would get a dip stick for it so you can tell, trannys aint nothing to be jacking with on the oil quantity. other than that something sounds wrong with the valve body. i would take it back out and look it over again make sure you did...

tek, i saw pictures of your shop, and um im not one to call someone a liar,,, but a b2????? maybe a little over the top. :D and i have no idea who told you were a grumpy old bast to your face, i thought we were only doing that on private messages behind your back :finger: clem, super nice job on the...

a couple things i can think of- did you let the clutch's soak for 24 hours in trans fluid before installing them? when you rebuilt the valve body are you 100% sure you got the bee bee's in the correct spots? and no tears in the gasket? is the vacume module good? and hooked up correctly to the manifo...

buddy thats past rust on the rear well.

i like the chop top, i have thought about doing it to mine but i am no body guy. i won't have a/c either so i am going to have to do something to get it cooled off in there.

anyhow how far are you from getting it running?