Search found 46 matches
- Thu Jun 25, 2009 6:52 am
- Forum: Bronco Tech
- Topic: Front end question
- Replies: 5
- Views: 1003
Front end question
My truck is doing this, and since noticing, I've seen other fords acting the same.... When the wheels are turned, the outside tire leans outward causing the outside edge of the tire to wear faster than the inside. I just put new wheel bearings in it, but like I said, the tire physically leans when t...
- Mon Jun 08, 2009 10:41 am
- Forum: Tools and Fabrication
- Topic: This has nothing to do with Bronco II
- Replies: 6
- Views: 8150
This has nothing to do with Bronco II
My "garage" as I'm calling it-- has no power. I need to get some light in there.
I have a car battery sitting around and a light fixture and switch. Can I put a 12 volt dc bulb and circuit it up to the battery?? will it burn my barn down or what? Fuses?
I have a car battery sitting around and a light fixture and switch. Can I put a 12 volt dc bulb and circuit it up to the battery?? will it burn my barn down or what? Fuses?
- Thu May 28, 2009 6:02 am
- Forum: Bronco Tech
- Topic: Interior lights stay on!
- Replies: 4
- Views: 801
Re: Interior lights stay on!
the dimmer switch works. The dash lights brighten and dim with the switch. how would i put a voltmeter on door switches to test them?
- Thu May 28, 2009 6:00 am
- Forum: Bronco Tech
- Topic: Interior lights stay on!
- Replies: 4
- Views: 801
Re: Interior lights stay on!
ok.. not that retarded
- Wed May 27, 2009 10:45 am
- Forum: On the Trail
- Topic: isnt anyone wheeling????
- Replies: 5
- Views: 1686
Re: isnt anyone wheeling????
I went this weekend! My buddy brought his camcorder but we eventually turned it off. It was bad luck to record anyhting!! :rolleyes2: the motor would get wet and cut off, then two minutes later start right up! :wtf: i don't know why..... also accidentally jumped that bad b*tch! LOL i was just tryin ...
- Wed May 27, 2009 10:27 am
- Forum: Bronco Tech
- Topic: Interior lights stay on!
- Replies: 4
- Views: 801
Interior lights stay on!
I'm half retarded when it comes to electrical troubleshooting. I don't feel bad saying that because a lot of you are too! HA Interior lights stay on all the time.. had to take the bulbs out. so, how do i check to find out what is causing the problem??
- Thu May 21, 2009 11:55 am
- Forum: Bronco Tech
- Topic: Noise in Tranny
- Replies: 24
- Views: 3662
Re: Noise in Tranny
Went and got some new wheels. Aluminum off the same ranger I got the tranny from. I got a feeling the noise I'm hearing is one of the motor mounts going bad.I guess next paycheck I'll be fixing that!
- Thu Apr 30, 2009 7:37 am
- Forum: Bronco Tech
- Topic: 92 ranger to 88 B2
- Replies: 5
- Views: 870
Re: 92 ranger to 88 B2
I heard the axles from the pickup were stronger. Would it even be worth doing if the biggest tires Im getting would be 31's?
- Thu Apr 30, 2009 6:07 am
- Forum: Bronco Tech
- Topic: 92 ranger to 88 B2
- Replies: 5
- Views: 870
Re: 92 ranger to 88 B2
They're both 4x4. So the rear would need some cutting a welding? And the front is just a bolt job?
- Wed Apr 29, 2009 8:21 am
- Forum: Bronco Tech
- Topic: 92 ranger to 88 B2
- Replies: 5
- Views: 870
92 ranger to 88 B2
Will front and rear axles from a '92 ext. cab ranger bolt onto an '88 b2 xlt?
- Wed Apr 29, 2009 5:34 am
- Forum: Bronco Tech
- Topic: Noise in Tranny
- Replies: 24
- Views: 3662
Re: Noise in Tranny
After driving her around for a while, I can say that every time the truck's weight is shifted to the left, it makes the noise. (Right turns, when the truck is rocking) I can't say for sure the axle or DS or trans is to blame, but I mainly feel the vibration through the gas pedal. It doesn't make a d...
- Mon Apr 27, 2009 7:49 am
- Forum: Bronco Tech
- Topic: Noise in Tranny
- Replies: 24
- Views: 3662
Re: Noise in Tranny
Here's the bad news. When I took off after fixin the carpet and all, I didn't notice i left the transfer case in 4L. So when it wasn't speeding up right I hit the gas a lil bit, which threw my foot back and repeated 3 times, :mad: then shifted to second and threw the transfer case to 2H without clut...
- Mon Apr 27, 2009 6:12 am
- Forum: Bronco Tech
- Topic: Noise in Tranny
- Replies: 24
- Views: 3662
Re: Noise in Tranny
Mazda tranny is installed! :D I got it on without takin the crossover pipes off. The manual transfer case shifter was in the same spot, but the gear shifter ended up about two inches closer to the motor. I cut the plate that was bolted to the floor and trimmed the plastic that the boots attach to an...
- Fri Apr 24, 2009 9:58 am
- Forum: Bronco Tech
- Topic: Lifting cheaply
- Replies: 2
- Views: 711
Lifting cheaply
I'm probably jumping the gun on this since my trucks not drivin yet.. but i'm trying to find cheap ways to lift my b2. If i put explorer springs in the front, would i need to do anything with the pitman arm or radius arms?
- Fri Apr 24, 2009 9:56 am
- Forum: Bronco Tech
- Topic: Noise in Tranny
- Replies: 24
- Views: 3662
Re: Noise in Tranny
Got the tranny last weekend. The shifters are different and the two electrical connections are on the opposite side. Shouldn't matter since my wires seemed to have enough slack. The mazda trans is about a half inch taller. I ended up cutting the crossover pipe on the ranger to get the trans out. Whe...