Search found 473 matches
- Sat Mar 13, 2010 8:24 pm
- Forum: Bronco Tech
- Topic: 2.9 Problem (won't Rev!)
- Replies: 15
- Views: 2418
Re: 2.9 Problem (won't Rev!)
ckeck cat converter, exhaust
- Sat Mar 13, 2010 8:18 pm
- Forum: Bronco Tech
- Topic: 2.9L problems. i need some help
- Replies: 9
- Views: 1569
Re: 2.9L problems. i need some help
the dizzy shaft runs off the lump shaft. i may be a redneck
- Thu Mar 11, 2010 8:04 pm
- Forum: Bronco Tech
- Topic: gmc drivetrain
- Replies: 3
- Views: 560
Re: gmc drivetrain
you might get warts putting a chevy into a B2
- Thu Mar 11, 2010 8:00 pm
- Forum: Bronco Tech
- Topic: valve cover gasket vs head gasket
- Replies: 11
- Views: 2037
Re: valve cover gasket vs head gasket
don't put silicon on both sides, it will push out. i use gasket sealer (it's like contact cement) on the valve cover side to hold gasket inplace while installing V/C
- Thu Mar 11, 2010 7:53 pm
- Forum: Bronco Tech
- Topic: abs
- Replies: 4
- Views: 729
Re: abs
check the ground at lower LH B-pillar, near ERBP module
- Thu Mar 11, 2010 7:48 pm
- Forum: Bronco Tech
- Topic: fusible links
- Replies: 1
- Views: 423
Re: fusible links
fuselinks are like big fuses. it burns before the wiring. could start fires or burn up other costly parts. i'd put another one back in.
- Thu Mar 11, 2010 7:41 pm
- Forum: Bronco Tech
- Topic: oil pressure rising slightly
- Replies: 7
- Views: 1255
Re: oil pressure rising slightly
always sitiing in the seat
- Tue Mar 09, 2010 9:03 pm
- Forum: Bronco Tech
- Topic: 2.9L problems. i need some help
- Replies: 9
- Views: 1569
Re: 2.9L problems. i need some help
or coil going out
- Tue Mar 09, 2010 9:02 pm
- Forum: Bronco Tech
- Topic: 2.9L problems. i need some help
- Replies: 9
- Views: 1569
Re: 2.9L problems. i need some help
backfire thru intake.... sounds like cracked rotor or cap, just throwing this at you.
- Tue Mar 09, 2010 8:46 pm
- Forum: Bronco Tech
- Topic: valve cover gasket vs head gasket
- Replies: 11
- Views: 2037
Re: valve cover gasket vs head gasket
if you don't think you can change the valve covers yourself, pay someone else to do it. I have bikes also, but if you can remove a barrel you can do this. taking the ALT off the right side makes it easy. all you need is a 10mm and make sure you clean everything, even the bolt holes. that should be t...
- Tue Mar 09, 2010 8:11 pm
- Forum: Bronco Tech
- Topic: oil pressure rising slightly
- Replies: 7
- Views: 1255
Re: oil pressure rising slightly
lower LH, front of engine
- Tue Mar 09, 2010 8:07 pm
- Forum: Bronco Tech
- Topic: a loud thump 88 xlt b2
- Replies: 4
- Views: 706
Re: a loud thump 88 xlt b2
check rad arm bushings
- Tue Mar 09, 2010 8:05 pm
- Forum: Bronco Tech
- Topic: 87 b2 wiring problems????????????
- Replies: 6
- Views: 1156
Re: 87 b2 wiring problems????????????
ok, you have spark but no fuel. correct? did you check the little ground wire on neg. side of battery?
- Thu Mar 04, 2010 4:50 pm
- Forum: Bronco Tech
- Topic: Another dumb question from me. Bronco ii 2.8 people.
- Replies: 8
- Views: 1327
Re: Another dumb question from me. Bronco ii 2.8 people.
besure to fill the cooling system up thru a heater hose so it don't air lock on you and overheat. this is important with these bottom t-stat motors.
- Mon Mar 01, 2010 5:01 pm
- Forum: Bronco Tech
- Topic: My '84 Bronco ii is dead.. overheating help.
- Replies: 9
- Views: 2286
Re: My '84 Bronco ii is dead.. overheating help.
put heat on that broken bolt before you try to take it out.