Search found 72 matches

by onewyr
Thu Jan 15, 2009 2:11 pm
Forum: Bronco Tech
Topic: this is how I trimmed 2" off of my rear fender
Replies: 3
Views: 1629

Re: this is how I trimmed 2" off of my rear fender

I doubt you will fit 33's with no lift on it even if you cut the 2 inches I have a 4" lift and 34" ltbs on mine and still rub. if you try to cut anymore out of the rear you will have to tub the rear fender wells. if you got anymore q's just ask.
by onewyr
Thu Sep 04, 2008 2:14 am
Forum: Bronco Tech
Topic: 89 b2 drive shaft
Replies: 2
Views: 898

Re: 89 b2 drive shaft

sounds like you bought an old old one some of the older b2s had a yoke on the back of the transfercase which if i am not mistaken you can swap yokes on the transfer case
by onewyr
Wed Sep 03, 2008 4:15 pm
Forum: Bronco Tech
Topic: hey quick quwstion for ya?
Replies: 5
Views: 1207

Re: hey quick quwstion for ya?

oh and the stock rear driveshafts take an instant crap with a lift... they suck already with stock ride then you take your tired driveshaft and add increased angle to it and in no time it goes crhshshshsh... and then you go buy another one at the junkyard and it craps out instantly too... so then u...
by onewyr
Fri Aug 29, 2008 1:22 pm
Forum: Bronco Tech
Topic: 2wd conversion
Replies: 7
Views: 2075

Re: 2wd conversion

BroncoII's don't have A arms they have beams
by onewyr
Fri Aug 29, 2008 4:55 am
Forum: Bronco Tech
Topic: 2wd conversion
Replies: 7
Views: 2075

Re: 2wd conversion

Most of the 2wd broncoII's came with a dummy transfer case so look for a dummy case and that way your rear driveshaft can stay the same. then you will need the factory drop brackets and front beams with the spindles. no your lift kit will not work with the 2wd bream. My question is why do you want t...
by onewyr
Thu May 01, 2008 3:17 pm
Forum: Bronco Tech
Topic: reamer size
Replies: 8
Views: 1797

Re: reamer size

maybe if you were more specific some one else might be able to be more specific. what are you trying to do.
by onewyr
Wed Apr 16, 2008 7:18 pm
Forum: Bronco Tech
Topic: On board air what to do
Replies: 2
Views: 967

On board air what to do

Alright I thought the 4.0 ac pump was no good for an onboard air system but some guys are using them on the explorer forum with success my question is what should I do I can't fit a york in the stock place so it is either the stocker or an electric like a viar 480c what kinda fill speeds can I expec...
by onewyr
Sat Apr 12, 2008 2:14 pm
Forum: Bronco Tech
Topic: Mounting Rad in back of Bronco
Replies: 5
Views: 1418

Re: Mounting Rad in back of Bronco

You should use aluminum piping it will help disipate heat but might get to cool
by onewyr
Thu Apr 10, 2008 6:11 pm
Forum: Bronco Tech
Topic: '93 sploder rpm problem look what wifey is getting
Replies: 2
Views: 921

'93 sploder rpm problem look what wifey is getting

I am going to pick up a '93 explorer for $400 the trans is bad but I have a question about the rpm's. at idle it runs smooth and if you press the accelerater slowly it revs nice but if you push the accelerator quickly the rpm's drop before it goes up any ideas would be great. here are some pics the ...
by onewyr
Thu Apr 10, 2008 2:15 am
Forum: Bronco Tech
Topic: rear disc brake question
Replies: 2
Views: 926

http://www.4x4central.com/discswap.html that page is for swapping the brakes from axle to axle but read it it tells you what to do about the mastercylinder I just got done with the same axle swap and I have not adjusted anything yet and it still has decent braking power I got to pull the master cyli...
by onewyr
Sun Apr 06, 2008 2:00 pm
Forum: Bronco Tech
Topic: WINDOW MOTOR
Replies: 9
Views: 2319

how bout posting a link to this so called rebuild kit
by onewyr
Thu Apr 03, 2008 3:22 pm
Forum: Bronco Tech
Topic: 9" or 8.8"
Replies: 14
Views: 2467

go get a 8.8" out of a 95 up explorer that gives you disc brake and most likely a limited slip that will help alot in the wheeling then save up some more and buy a new carrier and a locker the L/s was a big help when I put that axle in my truck I started with a 8.8 drum brake rear with a limite...
by onewyr
Tue Apr 01, 2008 4:40 pm
Forum: Bronco Tech
Topic: budget lift for my bII
Replies: 4
Views: 1586

I ran 32x11.50's with explorer springs, spacer in the front and a 2" trim job
Image
by onewyr
Fri Mar 28, 2008 6:58 pm
Forum: Bronco Tech
Topic: stuck in 4x4..
Replies: 3
Views: 1333

pull the shift motor and either clean it or replace it I think someone did as write up on cleaning it on TRS>com
by onewyr
Sun Mar 16, 2008 5:30 pm
Forum: Bronco Tech
Topic: Dana 44 SAS Pics
Replies: 8
Views: 2233

hey you forgot something. the back is feeling a little left out. JK looking good man keep it up and like the others said ditch the cinder blocks.
My jack stands are to short so I took A couple pieces of 6x6 and screwed them to a piece of 3/4 plywood to put under my stands