can any one tell me where The A/C Comp Throttle Cut-Off Relay is located:on my 1990 ford bronco ii as it said it was Under hood, driver side, front side of wheelwell, mounted in relay block (I don't find any relays at all there).
thanks darell
Search found 10 matches
- Thu Jul 11, 2013 12:33 pm
- Forum: Bronco Tech
- Topic: The A/C Comp Throttle Cut-Off Relay is located:
- Replies: 0
- Views: 4871
- Wed Aug 17, 2011 9:45 pm
- Forum: Tools and Fabrication
- Topic: Rebuild motor kit!!
- Replies: 2
- Views: 7559
Re: Rebuild motor kit!!
look for engine rebuild kits on e bay but stay a way from grumpys performance center in mulino or.
But make it a point to check clearance on rod and main bearing and check the pin on crank timing gear as I had one come out on me good luck
But make it a point to check clearance on rod and main bearing and check the pin on crank timing gear as I had one come out on me good luck
- Thu Aug 11, 2011 11:31 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
I put air in to the oil sending unit fitting and found that it can out like mad ""HIS HIS"" checked the mains Clearance with red Plasitgauge 0.009 no change could not find yellow Plasitgauge 0.009-0.020 checked with Caliper and a Micrometer to find the man at mech shop that was t...
- Fri Aug 05, 2011 9:32 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
Checked oil pump and screen, checked cam plate, checked oil up to rockers, oil filter, put new timing chain guide, pulled cam look's like bearing in ok, all galley plug in place; checked oil pressure with new gage 20 psi cold 0 psi hot at 180 degrees temp at factory idle 900 rpm pulling eng again st...
- Wed Jul 27, 2011 8:39 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
oil pump pickup tube and screen clean no old deposits no carbon eng only had 60,000 mile when burnet a pistion and cracked head
- Tue Jul 26, 2011 9:26 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
What is the exact PSI reading at factory idle and at 180 degrees temp? 0 psi
What is the Exact PSI reading at @ 1500 rpm at 2000 rpm and 2500 rpm when cold 25 /30 psi
and then when warm.10 / 20
yes engine was hot tanked
galley plugs not leaking or missing (installed front rear)
What is the Exact PSI reading at @ 1500 rpm at 2000 rpm and 2500 rpm when cold 25 /30 psi
and then when warm.10 / 20
yes engine was hot tanked
galley plugs not leaking or missing (installed front rear)
- Fri Jul 22, 2011 4:11 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
i just replaced Timing Chain Tensioner and Timing Chain Guide no change ????????? help what to do now change oil pump or pull eng and replace Camshaft Bearing agin ?????????????
- Tue Jul 19, 2011 7:31 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
yes put an accurate gauge on the engine, cam retention plate in right way oil 10-40 weight,oil up to valves, m shop say cam bearing installed right
- Mon Jul 18, 2011 5:50 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
Re: bronco tech
good oil pressure cool no oil pressure at running temp with 180 thermosat at itle rev up rpm pressure go's up
- Sun Jul 10, 2011 9:37 pm
- Forum: Bronco Tech
- Topic: bronco tech
- Replies: 18
- Views: 3140
bronco tech
ford 2.9 L low oil pressure after rebuilding eng I rebuild me eng new pistons .010, new rod & main bearings std., new cam bearings new cam, new oil pump, timing set, new heads, lifter, but after starting it it showes low oil pressure on gage rev eng oil pressure go's up but drops back down at i...