Search found 10 matches

by togosake
Thu Jul 11, 2013 12:33 pm
Forum: Bronco Tech
Topic: The A/C Comp Throttle Cut-Off Relay is located:
Replies: 0
Views: 875

The A/C Comp Throttle Cut-Off Relay is located:

can any one tell me where The A/C Comp Throttle Cut-Off Relay is located:on my 1990 ford bronco ii as it said it was Under hood, driver side, front side of wheelwell, mounted in relay block  (I don't find any relays at all there).
thanks darell
by togosake
Wed Aug 17, 2011 9:45 pm
Forum: Tools, Parts, and Fabrication
Topic: Rebuild motor kit!!
Replies: 2
Views: 1512

Re: Rebuild motor kit!!

look for engine rebuild kits on e bay but stay a way from grumpys performance center in mulino or.
But make it a point to check clearance on rod and main bearing and check the pin on crank timing gear as I had one come out on me good luck
by togosake
Thu Aug 11, 2011 11:31 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

I put air in to the oil sending unit fitting and found that it can out like mad ""HIS HIS"" checked the mains Clearance with red Plasitgauge 0.009 no change could not find yellow Plasitgauge 0.009-0.020 checked with Caliper and a Micrometer to find the man at mech shop that was t...
by togosake
Fri Aug 05, 2011 9:32 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

Checked oil pump and screen, checked cam plate, checked oil up to rockers, oil filter, put new timing chain guide, pulled cam look's like bearing in ok, all galley plug in place; checked oil pressure with new gage 20 psi cold 0 psi hot at 180 degrees temp at factory idle 900 rpm pulling eng again st...
by togosake
Wed Jul 27, 2011 8:39 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

oil pump pickup tube and screen clean no old deposits no carbon eng only had 60,000 mile when burnet a pistion and cracked head
by togosake
Tue Jul 26, 2011 9:26 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

What is the exact PSI reading at factory idle and at 180 degrees temp? 0 psi
What is the Exact PSI reading at @ 1500 rpm at 2000 rpm and 2500 rpm when cold 25 /30 psi
and then when warm.10 / 20

yes engine was hot tanked
galley plugs not leaking or missing (installed front rear)
by togosake
Fri Jul 22, 2011 4:11 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

i just replaced Timing Chain Tensioner and Timing Chain Guide no change ????????? help what to do now change oil pump or pull eng and replace Camshaft Bearing agin ?????????????
by togosake
Tue Jul 19, 2011 7:31 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

yes put an accurate gauge on the engine, cam retention plate in right way oil 10-40 weight,oil up to valves, m shop say cam bearing installed right
by togosake
Mon Jul 18, 2011 5:50 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

Re: bronco tech

good oil pressure cool no oil pressure at running temp with 180 thermosat at itle rev up rpm pressure go's up
by togosake
Sun Jul 10, 2011 9:37 pm
Forum: Bronco Tech
Topic: bronco tech
Replies: 18
Views: 572

bronco tech

[b]ford 2.9 L low oil pressure after rebuilding eng I rebuild me eng new pistons .010, new rod & main bearings std., new cam bearings new cam, new oil pump, timing set, new heads, lifter, but after starting it it showes low oil pressure on gage rev eng oil pressure go's up but drops back down at...

Go to advanced search