Search found 20 matches

by wmmichael20
Sun Dec 02, 2012 7:52 am
Forum: Bronco Tech
Topic: 4 inch rough country question
Replies: 3
Views: 797

Re: 4 inch rough country question

it comes with the bumpstop drop brackets as well
by wmmichael20
Wed Feb 08, 2012 5:00 am
Forum: Tools, Parts, and Fabrication
Topic: welding tips
Replies: 14
Views: 3438

Re: welding tips

I've had good luck just clamping a piece of scotch brite or steel wool to the wire just before it goes through the rollers so it cleans itself off before it even hits the rollers and i dont have to remove the spool and refeed it through the gun every time i want to use it.
by wmmichael20
Tue Jan 31, 2012 7:13 pm
Forum: Bronco Tech
Topic: fuel pressure regulator 88 2.9 efi
Replies: 6
Views: 1711

Re: fuel pressure regulator 88 2.9 efi

pull the vaccum line off the back of it ....if its full of fuel then the regulator is junk .......thats how i figured out mine was bad
by wmmichael20
Tue Oct 25, 2011 4:00 am
Forum: Tools, Parts, and Fabrication
Topic: Looking for a quality lift kit
Replies: 4
Views: 1596

Re: Looking for a quality lift kit

rough country makes a 4 inch for under 500 dollars and comes with shocks
by wmmichael20
Thu Aug 04, 2011 6:27 am
Forum: Bronco Tech
Topic: help with getting bronco started?
Replies: 5
Views: 235

Re: help with getting bronco started?

is there sufficent spark ? is the coil weak or plug wires bad or plugs themselves need replaced ? just ideas
by wmmichael20
Thu Aug 04, 2011 6:25 am
Forum: Bronco Tech
Topic: How in the Heck.....
Replies: 5
Views: 240

Re: How in the Heck.....

the clips just slide out of the fittings just push a flat head screwdriver under the tabs on them and pry out then just pull the lines off or take the lines off at the filter canister on the frame rail .........you said u cant reach or see the lines on top of the tank .....let it down with a floor j...
by wmmichael20
Sun Mar 27, 2011 10:48 am
Forum: Bronco Tech
Topic: Ignition Problem
Replies: 4
Views: 310

Re: Ignition Problem

check the coil brother I have had the coil wire burn in half before on both my ranger and bronco ( kinda my fault on the ranger didnt put it back in the loom and it touched the exhaust manifold lol
by wmmichael20
Sun Mar 27, 2011 10:46 am
Forum: Bronco Tech
Topic: Starting off right
Replies: 9
Views: 480

Re: Starting off right

im with ranger dave the 4 inch will get you plenty of room in those wheel wells then the explorer axels will add the beef you need for the bigger tires and if you regear those axels there will be no need for the bigger engine the 2.9 with a rebuild will definately do the job and get decent fuel mile...
by wmmichael20
Mon Feb 21, 2011 11:53 am
Forum: Bronco Tech
Topic: Priming the oil pump
Replies: 2
Views: 251

Re: Priming the oil pump

you can always finish puting the engine in the truck and just pull the coil wire off and roll the engine over in intervals of 10 seconds about half a dozen times or more and watch for oil pressure to rise on the gauge b4 hooking the coil wire back up
by wmmichael20
Sat Feb 12, 2011 7:38 am
Forum: Bronco Tech
Topic: problems, problems, problems
Replies: 6
Views: 332

Re: problems, problems, problems

take it back or bleed the clutch slave cylinder out may be didnt get completely bled out and check the fluid level on the firewall
by wmmichael20
Wed Feb 09, 2011 6:37 am
Forum: Bronco Tech
Topic: lowering the hitch?
Replies: 9
Views: 555

Re: lowering the hitch?

have somone just heat up the nut on that old hitch ball with a torch and hold the ball with a pipe wrench and use a box end wrench to take the nut off that way you dont ruin your old hitch ball instead of cutting it off
by wmmichael20
Wed Dec 22, 2010 6:45 am
Forum: Bronco Tech
Topic: 31-10.5-15 tires on 15x10 wheels???
Replies: 2
Views: 643

Re: 31-10.5-15 tires on 15x10 wheels???

they will fit but its not recomended the wheels are accualy wider than the tread width of the tire and along with that the rim lip will have no protection from damage like curbs or rocks on the trail,and more prone to pop off the bead when aired down,it is accualy recomended to go approx 2 inches na...
by wmmichael20
Mon Dec 13, 2010 8:05 am
Forum: Bronco Tech
Topic: 1984 2.8 water inlet
Replies: 4
Views: 273

Re: 1984 2.8 water inlet

start junk yard searching
by wmmichael20
Wed Dec 01, 2010 6:18 am
Forum: Bronco Tech
Topic: ford wheels..
Replies: 4
Views: 303

Re: ford wheels..

yep ford used a 5 on 4.5 lug pattern on the ranger,bronco 2 and the explorer, jeep aslo used the same lug pattern on the wrangler from 87-2006, the xj cherokee in all years of production and the grand cherokee also dodge used the lug pattern in the mid to late 70s on there half ton pickups.
by wmmichael20
Wed Nov 10, 2010 5:03 am
Forum: Bronco Tech
Topic: transmission flush/fill
Replies: 19
Views: 1072

Re: transmission flush/fill

go to the parts store and look on there shelves for a manual I go mine as auto zone for 12 dollars i believe its a haynes , and the trans pan in on the bottom of your trans its big and flat and made of tin, the dip stick tube is where you fill your auto trans so get a small funnel and your power ste...

Go to advanced search