Search found 110 matches
- Sat Jun 03, 2006 9:51 pm
- Forum: Bronco Tech
- Topic: problem with the oil and gas
- Replies: 5
- Views: 1597
- Sat Jun 03, 2006 9:31 pm
- Forum: Bronco Tech
- Topic: Ranger cab on a Bronco frame
- Replies: 17
- Views: 4747
Night Krawler (NK) over at BroncoII.org is in the process of putting a ranger cab on his B2 frame.
http://broncoii.org/fordforum/index.php ... 138&st=200
http://broncoii.org/fordforum/index.php ... 138&st=200
- Sat Jun 03, 2006 8:15 pm
- Forum: Bronco Tech
- Topic: fabrication assistance needed
- Replies: 11
- Views: 2601
I made a set like that. First I made a set that had slots front to rear for the stud and dowel so I could adjust the engine's position, then I marked where in the slot it was and lifted the motor up took off the plates and used them as templates to make one like what you have pictured. They are actu...
- Fri Feb 17, 2006 3:49 am
- Forum: Bronco Tech
- Topic: Aftermarket shifter on a 302 conversion
- Replies: 4
- Views: 1317
I am using the stock shifter on my C6, I just played with the linkage. The shifter on the tranny had to move in the opposite direction as the stock tranny to go from park to drive so to fix that there is a bar with 2 tabs that mounts from the frame to tranny and has one bar connected to the shifter ...
- Sat Jan 28, 2006 5:34 am
- Forum: Bronco Tech
- Topic: little triangles
- Replies: 5
- Views: 1631
Here's a link to the weld on wedges from James Duff:
http://www.jamesduff.com/eb/suspension_components.html
I used these to set up F-150 radius arms on a F-250 D44 that was originally leaf sprung.
http://www.jamesduff.com/eb/suspension_components.html
I used these to set up F-150 radius arms on a F-250 D44 that was originally leaf sprung.
- Wed Jan 25, 2006 7:47 pm
- Forum: Bronco Tech
- Topic: Tell me about your rear end
- Replies: 16
- Views: 4034
A lot of Jeep guys are scrapping their D44's in favor of 8.8s since they are the same bolt pattern and much stronger. I went with a D60 8-lug full floater with a Trak-Lok diff in it, and I did a disc conversion on it too. I would recommend the 8.8 if you are staying somewhat stock and a 9 inch if yo...
- Wed Jan 25, 2006 7:41 pm
- Forum: Bronco Tech
- Topic: 302 fi or 302 carb
- Replies: 4
- Views: 1430
- Wed Jan 25, 2006 7:38 pm
- Forum: Bronco Tech
- Topic: 79 bronco axles in an 84 broncoII
- Replies: 27
- Views: 6071
I am using fulwidth axles. The leaf springs from a 88-99 1/2 ton chevy fit in out trucks nicely with the mounts for them moved and they give good lift and flex. I kept the stock shock/coil buckets but will most likely be switching to air shocks when I get home and get rid of both the coil and shock....
- Sun Jan 15, 2006 6:03 am
- Forum: Bronco Tech
- Topic: V8 Tcase Options in BII
- Replies: 7
- Views: 1954
I did a C6 and NP205, I made my own crossmember for it that is plenty strong but the NP205 also has a side mount on it to help with the weight. The NP208 is quite a bit too wide, and would take some creative frame mods. I think there is an chain drive BW T-case in some mid 80s trucks that is slightl...
- Sun Jan 15, 2006 4:46 am
- Forum: Bronco Tech
- Topic: forget the duraspark, Im going 302!
- Replies: 5
- Views: 2115
I was going to do the adapter route but found it to be a lot cheaper to swap in a C6-NP205 combo. You lose less power through the C-4 though and it is plenty strong. If you can find a C5 I would do the C4-C5 hybrid bolted to your stock T-case, but if not I would look for a C4 with a Dana 20 or NP205...
- Tue Jul 19, 2005 5:24 pm
- Forum: Bronco Tech
- Topic: Have you heard?
- Replies: 10
- Views: 2951
The Price is around $1800-$1900 but you are getting a lot more than a suspension lift. This is one of their stage 3 lifts which when compared to their smaller stage 3 lifts ($1670 for the 3 inch) isn't that much more. The lift comes with everything - progressive rate coils, new lift leafs, 6 new sho...
- Sat Jul 09, 2005 11:31 pm
- Forum: Bronco Tech
- Topic: Dana 44 leaf spring conversion?
- Replies: 10
- Views: 4207
I think that coils are easier, have some advantages over leafs, and personally used them. But I have to disagree about them giving more flex. I have seen alot of pics of leafs with mad flex, but as Nobody said flexy leafs give crazy driveshaft angles and axle wrap. Here one exaple of flexy front and...
- Sat Jul 09, 2005 9:36 pm
- Forum: Chit Chat
- Topic: i got rear ended!
- Replies: 7
- Views: 1816
I rear ended a lady in my tracker. I saw the back of her car completely smashed and got out expecting the front of mine to be as bad or worse but only saw a tiny dent in the edge of the hood :hmmm: She got out of the car and looked at the damage said her husband was gonna flip out about the new Niss...
- Sat Jul 09, 2005 9:15 pm
- Forum: Bronco Tech
- Topic: Early Bronco T-case
- Replies: 13
- Views: 3298
- Sat Jul 09, 2005 9:11 pm
- Forum: Bronco Tech
- Topic: new radeator
- Replies: 13
- Views: 3826